Mode d’emploi
- Copiez la commande et examinez le paquet avant de l’installer dans votre environnement agent.
- Consultez le document original pour les outils, identifiants et environnements requis.
- Décrivez les entrées et le livrable souhaité ; comparez la sortie aux sources.
npx skills add https://github.com/glincker/ableton-skills --skill sound-designerAvant de commencer
- L’installation n’inclut ni abonnement au modèle, ni quota API, ni accès aux fichiers.
- Étoiles et installations reflètent l’activité, pas un test indépendant de qualité ou de sécurité.
Document Skill original
Rendu depuis le dépôt source en conservant titres, exemples, code, tableaux, liens et images.
Sound Designer
Build synth patches from a description. Stock Ableton synths only — Operator (FM), Wavetable (wavetable + FM), Analog (subtractive), Drift (modern subtractive). User can swap to a third-party synth manually after.
Workflow
1. Pick the right synth
| Sound type | Best synth | Why |
|---|---|---|
| Sub bass, 808 | Operator (sine + saturation) or Drift | Pure low end, easy to control |
| Reese / Massive bass | Wavetable | Detuned saws + filter movement |
| Pluck / staccato | Operator | Fast envelopes, FM bite |
| Wide supersaw | Wavetable (saw table, unison 7+) | Native unison + detune |
| Lush pad | Wavetable (LP filter + slow envelopes) | Movement + filter LFO |
| Acoustic-y / felt | Drift + tape simulation | Warm character |
| Vintage analog lead | Analog | Authentic voicing |
| Bell / mallet | Operator (FM ratios) | Inharmonic partials |
2. Set base parameters
For each patch type, here's the starting point:
Sub bass (Operator)
- Algorithm: A only (single sine)
- Osc A: Sine, level 0 dB
- Filter: off
- Amp env: Attack 0, Decay 0, Sustain 1.0, Release 0.1
- Glide: 50ms (mono mode)
Wide supersaw (Wavetable)
- Osc 1: Saw 1 wavetable
- Unison: 7 voices, detune 25-35
- Filter 1: LP24, cutoff 80%, resonance 15%, env 30%
- Filter env: Attack 0, Decay 400ms, Sustain 50%, Release 200ms
- Amp env: A 5ms, D 200ms, S 80%, R 300ms
Lush pad (Wavetable)
- Osc 1: Choir/Vocal wavetable
- Osc 2: Saw, detuned -7 cents
- Filter LP24, cutoff 60%, resonance 10%
- Filter LFO: triangle, rate 0.1 Hz, amount 25%
- Amp env: A 800ms, D 1500ms, S 70%, R 2000ms
- Add chorus + Hall reverb on the chain
Pluck (Operator)
- Algorithm: B→A
- Op B (modulator): Ratio 2.0, fixed level
- Op A: Sine, level 0
- Filter: LP, cutoff 70%, env amount 40%
- Filter env: A 0, D 80ms, S 0%, R 100ms
- Amp env: A 0, D 200ms, S 0%, R 100ms
3. Add character with effects
After the synth, append:
- Saturator before filter (drive 3-6 dB) for warmth
- Chorus for width on pads/leads
- Auto Filter with LFO mod for movement
- Reverb send to Return A (Hall) — typical 20-30% on pads, 10-15% on leads
- Delay send to Return B (Ping Pong) — 15-20% on plucks/leads
- EQ Eight at the end of chain — surgical cut at any harsh resonance
4. Verify
Read back the parameters, confirm:
"Wavetable supersaw lead with 7-voice unison at 30 detune, LP24 filter at 80% with light env motion, chorus + 25% reverb send. Save as 'Wide Lead'?"
5. Save preset (if MCP supports)
save_device_preset to user's User Library if available. Otherwise tell user to save manually with Cmd+S on the device.
Don'ts
- Don't recommend third-party synths the user might not have (Serum, Massive, Diva, etc.) by default.
- Don't max out resonance — anything above 70% on Wavetable's filter risks self-oscillation that masks the patch.
- Don't load presets without inspecting first; the user may have favorites already on the track.
- Don't apply more than 6 effects in one chain — clarity over saturation.