사용 방법
- 설치 명령을 복사하고 자신의 에이전트 환경에 설치하기 전에 소스 패키지를 확인하세요.
- 필요한 도구, 인증 정보, 지원 환경은 원본 문서에서 확인하세요.
- 입력과 원하는 산출물을 설명하고 출처와 결과를 대조하세요.
npx skills add https://github.com/mohitmishra786/low-level-dev-skills --skill bus-drivers-i2c-spi시작 전 확인
- 설치에는 모델 구독, API 한도, 파일 접근 권한이 포함되지 않습니다.
- 별점 수와 설치 수는 활동 지표이며 독립적인 품질·보안 검증이 아닙니다.
원본 Skill 문서
원본 저장소의 제목, 예시, 코드, 표, 링크, 이미지를 유지해 표시합니다.
Bus Drivers (I2C and SPI)
Purpose
Guide agents through Linux I2C and SPI client drivers: bus registration, i2c_transfer / spi_sync, regmap abstraction, DT compatible on bus children, and probe patterns — complementing platform MMIO drivers in skills/kernel/device-drivers.
When to Use
- Sensor or PMIC on I2C/SPI bus
- Converting bare-metal SPI register reads to kernel driver
- Using
regmapfor multi-byte register access - Debugging
-EREMOTEIOor missing ACK
Workflow
1. I2C client driver
c
#include <linux/i2c.h>
#include <linux/mod_devicetable.h>
static int my_probe(struct i2c_client *client)
{
struct regmap *map;
map = devm_regmap_init_i2c(client, &my_regmap_config);
if (IS_ERR(map))
return PTR_ERR(map);
dev_info(&client->dev, "probed at 0x%02x\n", client->addr);
return 0;
}
static const struct of_device_id my_of_id[] = {
{ .compatible = "vendor,sensor" },
{ }
};
MODULE_DEVICE_TABLE(of, my_of_id);
static const struct i2c_device_id my_id[] = {
{ "mysensor", 0 },
{ }
};
MODULE_DEVICE_TABLE(i2c, my_id);
static struct i2c_driver my_driver = {
.probe = my_probe,
.remove = my_remove,
.driver = { .name = "mysensor", .of_match_table = my_of_id },
.id_table = my_id,
};
module_i2c_driver(my_driver);DT child:
dts
i2c1 {
sensor@48 {
compatible = "vendor,sensor";
reg = <0x48>;
};
};2. Raw I2C transfer
c
u8 reg = 0x0F, val;
struct i2c_msg msgs[] = {
{ .addr = client->addr, .flags = 0, .len = 1, .buf = ® },
{ .addr = client->addr, .flags = I2C_M_RD, .len = 1, .buf = &val },
};
ret = i2c_transfer(client->adapter, msgs, 2);3. SPI driver
c
static int spi_probe(struct spi_device *spi)
{
spi->mode = SPI_MODE_0;
spi->bits_per_word = 8;
spi_setup(spi);
struct spi_transfer t = {
.tx_buf = tx,
.rx_buf = rx,
.len = len,
};
struct spi_message m;
spi_message_init(&m);
spi_message_add_tail(&t, &m);
return spi_sync(spi, &m);
}
static struct spi_driver spi_drv = {
.probe = spi_probe,
.driver = { .name = "my-spi", .of_match_table = my_of_match },
};
module_spi_driver(spi_drv);4. regmap (preferred for register maps)
c
static const struct regmap_config my_regmap_config = {
.reg_bits = 8,
.val_bits = 8,
.max_register = 0x7F,
};
regmap_read(map, REG_STATUS, &val);
regmap_write(map, REG_CTRL, CTRL_ENABLE);
regmap_update_bits(map, REG_CTRL, MASK, ENABLE);5. Debug
bash
i2cdetect -y 1
i2cdump -y 1 0x48
cat /sys/bus/i2c/devices/i2c-1/1-0048/name6. Agent usage
/bus-drivers-i2c-spi Write regmap-based driver for I2C PMIC at 0x58Common Problems
| Symptom | Cause | Fix |
|---|---|---|
-EREMOTEIO | NACK — wrong address | i2cdetect; check reg in DT |
| SPI mode wrong | CPOL/CPHA mismatch | Match datasheet + spi->mode |
| Probe defer | Regulator/clock supplier | Return -EPROBE_DEFER |
| regmap -EIO | 16-bit vs 8-bit reg | Set reg_bits, val_bits |
| DMA not used | Small spi_sync OK | spi_sync_transfer for bulk |
Related Skills
skills/kernel/device-drivers— IRQ, DMA, PM runtimeskills/kernel-dev/device-tree— bus child nodesskills/baremetal/spi-i2c-baremetal— register-level protocolskills/kernel-dev/platform-device-model— driver model parallelsskills/kernel-dev/writing-char-drivers— expose sensor via char dev
