사용 방법
- 설치 명령을 복사하고 자신의 에이전트 환경에 설치하기 전에 소스 패키지를 확인하세요.
- 필요한 도구, 인증 정보, 지원 환경은 원본 문서에서 확인하세요.
- 입력과 원하는 산출물을 설명하고 출처와 결과를 대조하세요.
npx skills add https://github.com/mohitmishra786/low-level-dev-skills --skill gpio-baremetal시작 전 확인
- 설치에는 모델 구독, API 한도, 파일 접근 권한이 포함되지 않습니다.
- 별점 수와 설치 수는 활동 지표이며 독립적인 품질·보안 검증이 아닙니다.
원본 Skill 문서
원본 저장소의 제목, 예시, 코드, 표, 링크, 이미지를 유지해 표시합니다.
GPIO (Bare-Metal)
Purpose
Configure and use GPIO without HAL: input/output modes, alternate function mapping, pull-up/down, speed/slew, and pin-change interrupts for LEDs, buttons, and peripheral pin mux.
When to Use
- Blink LED or read button before bringing up UART/SPI
- Mux pins to USART/SPI alternate functions
- EXTI line interrupts on pin edges
- Porting GPIO code between vendors
Workflow
1. STM32 GPIO pattern
c
/* Enable GPIOA clock */
RCC->AHB1ENR |= RCC_AHB1ENR_GPIOAEN;
/* PA5 output — MODER[11:10] = 01 */
GPIOA->MODER &= ~(3U << (5 * 2));
GPIOA->MODER |= (1U << (5 * 2));
/* Toggle via BSRR — atomic set/reset */
GPIOA->BSRR = (1U << 5); /* set */
GPIOA->BSRR = (1U << (5+16)); /* reset */Alternate function (e.g., USART2 TX on PA2):
c
GPIOA->MODER &= ~(3U << (2*2));
GPIOA->MODER |= (2U << (2*2)); /* AF mode */
GPIOA->AFR[0] &= ~(0xFU << (2*4));
GPIOA->AFR[0] |= (7U << (2*4)); /* AF7 = USART2 */2. Input with pull-up
c
/* PC13 input, pull-up */
GPIOC->MODER &= ~(3U << (13*2)); /* input mode 00 */
GPIOC->PUPDR &= ~(3U << (13*2));
GPIOC->PUPDR |= (1U << (13*2)); /* pull-up */
int pressed = !(GPIOC->IDR & (1U << 13)); /* active low */3. EXTI interrupt (STM32)
c
/* SYSCFG: map EXTI13 to PC13 */
SYSCFG->EXTICR[3] = (SYSCFG->EXTICR[3] & ~0xFU) | 0x2; /* port C */
EXTI->IMR |= (1U << 13);
EXTI->FTSR |= (1U << 13); /* falling edge */
NVIC_EnableIRQ(EXTI15_10_IRQn);ISR: check EXTI->PR, clear with write-1.
4. nRF52 / ESP32 notes
| Platform | Pattern |
|---|---|
| nRF52 | NRF_P0->PIN_CNF[n] — direction, pull, drive |
| ESP32 | GPIO.out_w1ts, GPIO.enable; IO_MUX for function |
Always enable peripheral clock / power domain before pin config.
5. Agent usage
/gpio-baremetal Configure PA2 as USART2 TX alternate function on STM32F4Common Problems
| Symptom | Cause | Fix |
|---|---|---|
| Pin stuck | Wrong MODER / not AF | Re-read RM pin table |
| EXTI storm | No debounce / floating input | Enable pull; debounce in software |
| AF mismatch | Wrong AFR nibble | Pin-specific AF table in RM |
| No toggle visible | Wrong port bit / LED active low | Check schematic |
Related Skills
skills/baremetal/mmio-and-bit-manipulation— BSRR/MODER masksskills/baremetal/peripherals-from-datasheet— RM pinout tablesskills/baremetal/uart-serial-baremetal— AF mux for serial
