Verwendung
- Installationsbefehl kopieren und das Quellpaket vor der Installation in der eigenen Agentenumgebung prüfen.
- Benötigte Werkzeuge, Zugangsdaten und Hosts im Original prüfen.
- Eingabe und gewünschtes Ergebnis beschreiben und die Ausgabe mit den Quellen abgleichen.
npx skills add https://github.com/mohitmishra786/low-level-dev-skills --skill protocol-analysisVor dem Start
- Die Installation umfasst weder Modellabo noch API-Kontingent oder Dateizugriffsrechte.
- Sterne und Installationen zeigen Aktivität, keine unabhängige Qualitäts- oder Sicherheitsprüfung.
Originales Skill-Dokument
Aus dem Quell-Repository gerendert; Überschriften, Beispiele, Code, Tabellen, Links und Bilder bleiben erhalten.
Protocol Analysis (I2C / SPI / UART)
Purpose
Guide agents through software-side serial bus analysis: logic analyzer workflow, sigrok/PulseView decoding, correlating captures with firmware drivers, and Python-based parsing — bridging skills/baremetal/spi-i2c-baremetal and hardware bring-up.
When to Use
- Sensor not responding — verify clock and data on bus
- Compare kernel driver transactions vs datasheet
- Document expected transaction format for CI/regression
- Teaching protocol layers without expensive lab gear (sim + decode)
Workflow
1. Capture stack
Physical probe → logic analyzer hardware (or GPIO bit-bang)
├── sigrok-cli / PulseView GUI
├── Protocol decoder (i2c, spi, uart)
└── Export VCD/CSV for scriptsOpen-source: sigrok with cheap FX2LA boards.
2. PulseView quick start
bash
# List devices
pulseview
# CLI capture (device-dependent)
sigrok-cli --driver fx2lafw --config samplerate=1MHz \
--channels 0=SDA,1=SCL \
--samples 1m \
--protocols i2c3. I2C decode expectations
| Phase | Lines |
|---|---|
| START | SDA fall while SCL high |
| Address + R/W | 7 bits + ACK |
| Data bytes | ACK per byte |
| STOP | SDA rise while SCL high |
NACK at address → wrong 0x48 or device held in reset.
4. SPI decode
Check mode (CPOL/CPHA), bit order (MSB first typical), CS polarity, and word size. Compare to spi_setup() in skills/kernel-dev/bus-drivers-i2c-spi.
5. UART decode
Set baud (9600/115200), frame (8N1), and signal polarity. Async — sample rate must be ≥ 4× baud for LA.
6. Python post-process (csv)
python
import csv
with open("capture.csv") as f:
for ts, ch0, ch1 in csv.reader(f):
# edge detect, reconstruct bits
pass7. Correlate with firmware
Logic capture timestamp
├── Match driver reg write sequence
├── Compare inter-byte delay vs datasheet max
└── Flag extra clock pulses (mode fault)8. Agent usage
/protocol-analysis Decode this I2C capture — device NACKs after register 0x0F writeCommon Problems
| Symptom | Cause | Fix |
|---|---|---|
| Garbage decode | Wrong samplerate | ≥ 4× bus speed |
| Floating lines | Missing pull-ups | Enable internal pull or external |
| SPI shifted bits | Mode mismatch | CPOL/CPHA table from RM |
| UART framing errors | Baud drift | Measure actual bit time |
| No decoder | Missing sigrok build | Install sigrok-cli + decoders |
Related Skills
skills/baremetal/spi-i2c-baremetal— firmware-side protocolskills/baremetal/uart-serial-baremetal— UART configskills/kernel-dev/bus-drivers-i2c-spi— kernel transactionsskills/profilers/strace-ltrace— userspace syscall trace analogskills/embedded/openocd-jtag— scope alongside SWD debug
