mohitmishra786/low-level-dev-skills

protocol-analysis

Protocol analysis skill for serial bus debugging.

Vedi sorgente

Come usare

  1. Copia il comando e controlla il pacchetto prima di installarlo nel tuo ambiente agente.
  2. Controlla strumenti, credenziali e ambienti richiesti nel documento originale.
  3. Descrivi input e risultato desiderato; confronta l’output con le fonti.
npx skills add https://github.com/mohitmishra786/low-level-dev-skills --skill protocol-analysis

Prima di iniziare

  • L’installazione non include abbonamenti, quote API o accesso ai file.
  • Stelle e installazioni indicano attività, non un test indipendente di qualità o sicurezza.
Documento Skill originale

Contenuto dal repository con titoli, esempi, codice, tabelle, link e immagini preservati.

Protocol Analysis (I2C / SPI / UART)

Purpose

Guide agents through software-side serial bus analysis: logic analyzer workflow, sigrok/PulseView decoding, correlating captures with firmware drivers, and Python-based parsing — bridging skills/baremetal/spi-i2c-baremetal and hardware bring-up.

When to Use

  • Sensor not responding — verify clock and data on bus
  • Compare kernel driver transactions vs datasheet
  • Document expected transaction format for CI/regression
  • Teaching protocol layers without expensive lab gear (sim + decode)

Workflow

1. Capture stack

Physical probe → logic analyzer hardware (or GPIO bit-bang)
├── sigrok-cli / PulseView GUI
├── Protocol decoder (i2c, spi, uart)
└── Export VCD/CSV for scripts

Open-source: sigrok with cheap FX2LA boards.

2. PulseView quick start

bash
# List devices
pulseview

# CLI capture (device-dependent)
sigrok-cli --driver fx2lafw --config samplerate=1MHz \
  --channels 0=SDA,1=SCL \
  --samples 1m \
  --protocols i2c

3. I2C decode expectations

PhaseLines
STARTSDA fall while SCL high
Address + R/W7 bits + ACK
Data bytesACK per byte
STOPSDA rise while SCL high

NACK at address → wrong 0x48 or device held in reset.

4. SPI decode

Check mode (CPOL/CPHA), bit order (MSB first typical), CS polarity, and word size. Compare to spi_setup() in skills/kernel-dev/bus-drivers-i2c-spi.

5. UART decode

Set baud (9600/115200), frame (8N1), and signal polarity. Async — sample rate must be ≥ 4× baud for LA.

6. Python post-process (csv)

python
import csv

with open("capture.csv") as f:
    for ts, ch0, ch1 in csv.reader(f):
        # edge detect, reconstruct bits
        pass

7. Correlate with firmware

Logic capture timestamp
├── Match driver reg write sequence
├── Compare inter-byte delay vs datasheet max
└── Flag extra clock pulses (mode fault)

8. Agent usage

/protocol-analysis Decode this I2C capture — device NACKs after register 0x0F write

Common Problems

SymptomCauseFix
Garbage decodeWrong samplerate≥ 4× bus speed
Floating linesMissing pull-upsEnable internal pull or external
SPI shifted bitsMode mismatchCPOL/CPHA table from RM
UART framing errorsBaud driftMeasure actual bit time
No decoderMissing sigrok buildInstall sigrok-cli + decoders

Related Skills

  • skills/baremetal/spi-i2c-baremetal — firmware-side protocol
  • skills/baremetal/uart-serial-baremetal — UART config
  • skills/kernel-dev/bus-drivers-i2c-spi — kernel transactions
  • skills/profilers/strace-ltrace — userspace syscall trace analog
  • skills/embedded/openocd-jtag — scope alongside SWD debug

Correlati per attività

dallo stesso repository

Altri Skills

Tutti gli Skills
mohitmishra786
Community

low-power-embedded

Low-power embedded skill for sleep modes and energy optimization. Use when configuring MCU sleep/stop/standby, peripheral clock gating, wake-up sources, or measuring firmware current draw. Activates on queries about WFI, STOP mode, STM32 PWR, nRF sleep, wake-up EXTI, or reducing embedded power consumption.

Installazioni / 1h
1
GitHub Stars
296
Aggiornato
20 nov
mohitmishra786
Community

core-dumps

Core dump analysis skill for production crash triage. Use when loading core files in GDB or LLDB, enabling core dump generation on Linux/macOS, mapping symbols with debuginfo or debuginfod, or extracting backtraces from crashes without re-running the program. Activates on queries about core files, ulimit, coredumpctl, debuginfod, crash triage, or analyzing segfaults from production binaries.

Installazioni / 1h
2
GitHub Stars
267
Aggiornato
27 giu
mohitmishra786
Community

custom-allocators

Custom allocator skill for memory allocation strategies. Use when implementing pool/slab/arena allocators, tuning jemalloc/mimalloc, writing Rust GlobalAlloc, or benchmarking allocator performance. Activates on queries about jemalloc, mimalloc, tcmalloc, arena allocator, GlobalAlloc, or fragmentation.

Installazioni / 1h
2
GitHub Stars
267
Aggiornato
27 giu
mohitmishra786
Community

ebpf

eBPF skill for Linux observability and networking. Use when writing eBPF programs with libbpf or bpftrace, attaching kprobes/tracepoints/XDP hooks, debugging verifier errors, working with eBPF maps, or achieving CO-RE portability across kernel versions. Activates on queries about eBPF, bpftool, bpftrace, XDP programs, libbpf, verifier errors, eBPF maps, or kernel tracing with BPF.

Installazioni / 1h
2
GitHub Stars
267
Aggiornato
27 giu